Electrically/Thermally Conductive Adhesives (ETC)

We offer a broad line of electrically and thermally conductive materials, which provide solutions to a variety of electrical, electronic, and thermal design problems throughout the laboratories and industries.

Properties Electrically/Thermally Conductive

Product Number 525 556 597A 598FS
Filler Silver Silver Silver Nickel
Mix Ratio

REF: D50380 Categories: ,

Available Options:

Description

We offer a broad line of electrically and thermally conductive materials, which provide solutions to a variety of electrical, electronic, and thermal design problems throughout the laboratories and industries.

Properties Electrically/Thermally Conductive

Product Number 525 556 597A 598FS
Filler Silver Silver Silver Nickel
Mix Ratio by Weight: Resin : Hardener NA 1:1 NA NA
Mixes Specific Gravity, g/cc @ 25°C 1.85 2.8 2.3/2.1 2.87/1.5
Mixes Viscosity, @ 25°C, cps Paste Paste Paste/Paste Paste/480
Pot Life, 100g mass @ 25°C, hrs. N/A 1 N/A N/A
Recommended Cure, hr/°F 2/300 24/RT 2/RT+2/200 2RT+2/200
Alternative Cure, hr/°F 6/250 4/170 or 2/210
Temperature Resistance, °F (°C) 340 (171) 340 (171) 1200 (649) 1000 (538)
CTE, in/in/°F x 106 (°C) 29.0 (52.2) 13.9 (25.0) 9.6 (17.3) 6.5 (11.7)
Thermal Conductivity, Btu-in/hr-ft2-°F 62.2 65.0 63.1 17.9
Tensile Shear Strength, psi * 2,500 1,500
Volume Resistivity, ohm-cmv 0.01 0.0052 0.0002 0.005
Dielectric Strength, volts/mil
Chemical Resistance Excellent Excellent Excellent Excellent
Color Silver Silver Silver Dark Gray

Properties Thermally Conductive

Product Number 568 805 860
Filler Aluminum Aluminum Aluminum Nitride
Mix Ratio by Weight: Resin : Hardener 1:1 100:12 1:1
Mixes Specific Gravity, g/cc @ 25°C .85 1.66 1.9
Mixes Viscosity, @ 25°C, cps Paste 85,000 Paste
Pot Life, 100g mass @ 25°C, hrs. 4.0 ≤1.0 4.0
Recommended Cure, hr/°F 2/200 2/100+2/200 2/200
Alternative Cure, hr/°F 24-48/RT 24-48/RT 24-48/RT
Temperature Resistance, °F (°C) 400 (204) 572 (300) 400 (204)
CTE, in/in/°F x 106 (°C) 33.0 (60.0) 25.0 (45.0) 18.7 (33.3)
Thermal Conductivity, Btu-in/hr-ft2-°F 9.0 12.5 8.5
Tensile Shear Strength, psi * 1,400 1,200 1,375
Volume Resistivity, ohm-cm 1.0 x 105 1.0 x 1014 1.0 x 1014
Dielectric Strength, volts/mil 80 50 250
Chemical Resistance Excellent Good Excellent
Color Grey Grey Grey

* Tested according to ASTM D1002-94. This is a standard test method for determining the shear strength of a single lap-joint metal coupons in tension loading.

Application Notes:
Surface Preparation: All surfaces must be free of oil, dirt, corrosives, oxides, paint or other foreign matter.
Mixing: Two-component products should be mixed thoroughly to a uniform consistency. Preheat high viscosity epoxies to approximately 125°F to facilitate pouring and mixing.
Application: In most cases, the adhesive should be applied to both surfaces maintaining a glue line of less than 10 mils (25.4 µm). After assembling the parts, pressure should be applied to the assembly to prevent warpage and reduce air entrapment. Refer to curing guidelines in above property chart.

Storage : RT

MSDS_50380-525

MSDS_50380-556A

MSDS_50380-556B

MSDS_50380-598

MSDS_50380-568A

MSDS_50380-568B

MSDS_50380-805A

MSDS_50380-805B

MSDS_50380-860A

MSDS_50380-860B

 

Additional information

Quantity

5g, 2x25g, 50g

Reviews

There are no reviews yet.

Be the first to review “Electrically/Thermally Conductive Adhesives (ETC)”

Your email address will not be published.

0

Your Cart