.png?strip=all&lossy=1&sharp=1&ssl=1){kind=small}
.png?strip=all&lossy=1&sharp=1&ssl=1){kind=small}
Showing all 34 results
Filters
Sort results
Reset
Apply
 |
No more stickiness with new storage boxMost resins are no longer a challenge to flat… Show more (+) No more stickiness with new storage boxMost resins are no longer a challenge to flat embed when used in combination with the Cocoon box. The system withstands temperatures up to 70 Degrees C, and our flat embedding of many resins is made easier. Show less (-) |
 |
Injected molded polyethyleneResistant to most embedding materialsEasy peeled-off the blocksMold fits perfectly inside the cocoon… Show more (+) Injected molded polyethyleneResistant to most embedding materialsEasy peeled-off the blocksMold fits perfectly inside the cocoon box BE8 (64300-8); See Cocoon Box section.These molds are reusable. Each cavity measures 12mm L x 5mm W x 3.5 mm D. Overall mold measures: 94 x 56 x 14 mm. Show less (-) |
 |
Machined from PTFE block. This mold offers flat embedding for most resins, including LR White®… Show more (+) Machined from PTFE block. This mold offers flat embedding for most resins, including LR White®, LR Gold®, JB-4, Immuno-Bed and Lowicryl®. This PTFE Flat Embedding Mold can be used for both UV/low temperature and thermal cure, and may be used as a substitution for the silicone molds. The individual cavities are pre-shaped to reduce block trimming. Show less (-) |
 |
Made from colored clear silicone, more flexible. These molds are reusable. For all Epoxy resin2… Show more (+) Made from colored clear silicone, more flexible. These molds are reusable. For all Epoxy resin2 different cavity sizes14 Cavities: 14 x 5 x 3 mm thick13 Cavities: 14,5 x 7 x 3 mm thick Show less (-) |
 |
Preparing a sample for a transmission electron microscope is a long and difficult process. These… Show more (+) Preparing a sample for a transmission electron microscope is a long and difficult process. These slice capsules were designed to simplify the preparation of samples and make the process more time efficient.Slice Capsules TDS Show less (-) |
 |
Uses a 1 x 3" glass slide as a base, and duplicates the slide using… Show more (+) Uses a 1 x 3" glass slide as a base, and duplicates the slide using the resin of your choice. Tissue sections are embedded against the flat glass surface. This duplicated resin slide can be studied under the Light Microscope, then cut, remounted, resectioned, and studied under the EM. A three cavity mold, each cavity measuring: 1" W x 3" L x 3/32" D. Reference & Instructions enclosed Show less (-) |
 |
The same design as above 70170 but with the addition of three round cavities which… Show more (+) The same design as above 70170 but with the addition of three round cavities which are 17 mm in diameter and 1 mm Deep. Show less (-) |
 |
Made from clear silicone, the overall measurements are 1.65" x 3" with 12 cavities… Show more (+) Made from clear silicone, the overall measurements are 1.65" x 3" with 12 cavities. Each cavity measures 0.427" L x 0.25" W x 0.156" D (10 mm L x 6 mm W x 4 mm D). This mold produces 12 embedding blocks with tapered ends. Show less (-) |
 |
EMS Embedding Mold is a new mold designed with Michael J. Dykstra Ph.D. from… Show more (+) EMS Embedding Mold is a new mold designed with Michael J. Dykstra Ph.D. from North Carolina State University Department of Veterinary Medicine. This Mold produces blocks of the best dimension to be held securely by Reichert/Leica Ultracut stepped microtome chucks. There are 24 cavities and the depth of each cavity is 4mm which will prevent breakage of the blocks during razor blade trimming.Mold Measurements: 3⅜" x 3" (85 x 77 mm)Cavity Measurements: 15 mm x 7 mm x 4 mm Deep Show less (-) |
 |
This mold is designed primarily for embedding cell culture specimens grown either directly on the… Show more (+) This mold is designed primarily for embedding cell culture specimens grown either directly on the bottom of a dish or on the filter when cross sections of the cells are needed Show less (-) |
