.png?strip=all&lossy=1&sharp=1&ssl=1){kind=small}
.png?strip=all&lossy=1&sharp=1&ssl=1){kind=small}
Showing all 49 results
Filters
Sort results
Reset
Apply
 |
The same design as above 70170 but with the addition of three round cavities which… Show more (+) The same design as above 70170 but with the addition of three round cavities which are 17 mm in diameter and 1 mm Deep. Show less (-) |
 |
Made from clear silicone, the overall measurements are 1.65" x 3" with 12 cavities… Show more (+) Made from clear silicone, the overall measurements are 1.65" x 3" with 12 cavities. Each cavity measures 0.427" L x 0.25" W x 0.156" D (10 mm L x 6 mm W x 4 mm D). This mold produces 12 embedding blocks with tapered ends. Show less (-) |
 |
EMS Embedding Mold is a new mold designed with Michael J. Dykstra Ph.D. from… Show more (+) EMS Embedding Mold is a new mold designed with Michael J. Dykstra Ph.D. from North Carolina State University Department of Veterinary Medicine. This Mold produces blocks of the best dimension to be held securely by Reichert/Leica Ultracut stepped microtome chucks. There are 24 cavities and the depth of each cavity is 4mm which will prevent breakage of the blocks during razor blade trimming.Mold Measurements: 3⅜" x 3" (85 x 77 mm)Cavity Measurements: 15 mm x 7 mm x 4 mm Deep Show less (-) |
 |
This mold is designed primarily for embedding cell culture specimens grown either directly on the… Show more (+) This mold is designed primarily for embedding cell culture specimens grown either directly on the bottom of a dish or on the filter when cross sections of the cells are needed Show less (-) |
 |
The Embedding Capsule SubstituteIt is easier to see inside the well when centering the… Show more (+) The Embedding Capsule SubstituteIt is easier to see inside the well when centering the specimen in the tipIt is easier to remove the block from the well. There is no need for razor blades or press devicesThe finished blocks have finer tips so when you trim deeper into the block the face doesn't increase in size rapidly; therefore, constant retrimming is not necessary Show less (-) |
 |
The Mold for Long TissuesThis mold accommodates longer pieces of tissues (muscle, skin biopsies, and… Show more (+) The Mold for Long TissuesThis mold accommodates longer pieces of tissues (muscle, skin biopsies, and many plant specimens)AdvantagesEasy to embed long specimens and orient them properly. The tissues lie flat in the well; therefore, no horizontal trimming is neededIt is ideal for any specimen that needs immediate sectioning (e.g. cell monolayer). 24 cavities Show less (-) |
 |
The mold yields several individual blocks of resin from a single slip-coverThe resin blocks fit… Show more (+) The mold yields several individual blocks of resin from a single slip-coverThe resin blocks fit directly into a chuck for flat specimensThe embedded surfaces are free from blemishes caused by entrapped airThe mold uses a minimum amount of resin Show less (-) |
 |
Machined from aluminum rods with one end tapered to 4.8mm in diameter. The specimen… Show more (+) Machined from aluminum rods with one end tapered to 4.8mm in diameter. The specimen can be oriented and mounted to the tip with glue and it is ready for sectioning. The body size is "00" and it measures 11mm long. Show less (-) |
 |
A new design with 10 triple numbered, tapered tip cavities to save you time and… Show more (+) A new design with 10 triple numbered, tapered tip cavities to save you time and handling. Holds firmly in a chuck during trimming or sectioning. Made from white silicone, each cavity measures 8mm from tip to center, 5mm Deep. Show less (-) |
