.png){kind=small}
.png){kind=small}
Showing all 49 results
Filters
Sort results
Reset
Apply
 |
Flat Embedding CrystalObserving the ultrastructure of cells under an electron microscope is an important aspect… Show more (+) Flat Embedding CrystalObserving the ultrastructure of cells under an electron microscope is an important aspect of biological research, especially in the neurosciences. These embedding crystals were designed to simplify the preparation of samples and make the process more time efficient. Show less (-) |
 |
A clear silicone rubber with very high tear strength. It can be reused more times… Show more (+) A clear silicone rubber with very high tear strength. It can be reused more times than the conventional silicone molds. It is resistant to most epoxy resins and its clear base allows positioning of the specimen lighted from beneath. Show less (-) |
 |
No more stickiness with new storage boxMost resins are no longer a challenge to flat… Show more (+) No more stickiness with new storage boxMost resins are no longer a challenge to flat embed when used in combination with the Cocoon box. The system withstands temperatures up to 70 Degrees C, and our flat embedding of many resins is made easier. Show less (-) |
 |
This Multi-Task BEEM Capsule Holder is an innovative holder designed to hold size "00" BEEM… Show more (+) This Multi-Task BEEM Capsule Holder is an innovative holder designed to hold size "00" BEEM capsule during resin polymerization. Show less (-) |
 |
Injected molded polyethyleneResistant to most embedding materialsEasy peeled-off the blocksMold fits perfectly inside the cocoon… Show more (+) Injected molded polyethyleneResistant to most embedding materialsEasy peeled-off the blocksMold fits perfectly inside the cocoon box BE8 (64300-8); See Cocoon Box section.These molds are reusable. Each cavity measures 12 mm (L) x 5 mm (W) x 3.5 mm Deep. Overall mold measures: 94 x 56 x 14 mm. Show less (-) |
 |
Injected molded polyethyleneResistant to most embedding materialsEasy peeled-off the blocksMold fits perfectly inside the cocoon… Show more (+) Injected molded polyethyleneResistant to most embedding materialsEasy peeled-off the blocksMold fits perfectly inside the cocoon box BE8 (64300-8); See Cocoon Box section.These molds are reusable. Each cavity measures 12mm L x 5mm W x 3.5 mm D. Overall mold measures: 94 x 56 x 14 mm. Show less (-) |
 |
Machined from PTFE block. This mold offers flat embedding for most resins, including LR White®… Show more (+) Machined from PTFE block. This mold offers flat embedding for most resins, including LR White®, LR Gold®, JB-4, Immuno-Bed and Lowicryl®. This PTFE Flat Embedding Mold can be used for both UV/low temperature and thermal cure, and may be used as a substitution for the silicone molds. The individual cavities are pre-shaped to reduce block trimming. Show less (-) |
 |
Made from colored clear silicone, more flexible. These molds are reusable. For all Epoxy resin2… Show more (+) Made from colored clear silicone, more flexible. These molds are reusable. For all Epoxy resin2 different cavity sizes14 Cavities: 14 x 5 x 3 mm thick13 Cavities: 14,5 x 7 x 3 mm thick Show less (-) |
 |
Preparing a sample for a transmission electron microscope is a long and difficult process. These… Show more (+) Preparing a sample for a transmission electron microscope is a long and difficult process. These slice capsules were designed to simplify the preparation of samples and make the process more time efficient.Slice Capsules TDS Show less (-) |
 |
Uses a 1 x 3" glass slide as a base, and duplicates the slide using… Show more (+) Uses a 1 x 3" glass slide as a base, and duplicates the slide using the resin of your choice. Tissue sections are embedded against the flat glass surface. This duplicated resin slide can be studied under the Light Microscope, then cut, remounted, resectioned, and studied under the EM. A three cavity mold, each cavity measuring: 1" W x 3" L x 3/32" D. Reference & Instructions enclosed Show less (-) |
